Can I Install a Bath Tub Myself? Considerations And Actions
Can I Install a Bath Tub Myself? Considerations And Actions
Blog Article
They are making a few good points regarding Installing A Bathtub in general in this great article beneath.
Setting up a bath tub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately difficult project. If the old tub is easily accessible, the task can relocate easily; if you need to open up a wall surface to get rid of the old bathtub and also place the new bathtub, the task is much harder. In either case, the project is within a house handyman's skills, although you will need a helper to leave the old tub as well as embeded in the new one. Make certain you have actually certified yourself for the work and also are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is far better to consider employing one prior to you start. Chances are you may need a specialist plumber to make tube links.
This article will assist you set up a brand-new bath tub in your bathroom if you have actually already acquired a new tub and don't need to alter the setup of your previous water supply pipes.
Your devices and also product checklist should comprise the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, activate the faucets to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be fairly bothersome as a result of the restricted gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will come from the pipelines. When the supply pipelines have been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Prior to going on to fit the brand-new taps, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the tap in place with the producer offered backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet ports. The former kind must be linked to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bathtub
Utilizing the two wood boards under its feet, put the bathtub in the needed setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 little points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub until the level reads degree.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the supply of water and examine all joints as well as brand-new pipework for leaks and tighten them if needed. Load the tub as well as likewise examine the overflow outlet and the typical outlet for leakages.
Lastly, fix the bathroom paneling as described in the maker's instruction manual. Tiling as well as sealing around the tub should wait up until the bath tub has been made use of a minimum of once as this will certainly settle it right into its last setting.
Planning for the Installment
First of all, the sustaining frame provided with the bathroom needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop pressure on the bathtub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be fitted in its final setting.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to crack an inflexible seal, creating the water to penetrate the wall between the bath as well as the tiling, resulting in problems with moisture as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your components and also installations. They are marketed in tubes as well as cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to always fill the bath tub with water prior to securing, to enable the movement experienced when the tub remains in usage. The sealant can break fairly early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily readily available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our article on How to Install a Bathtub. Thank you so much for finding the time to read through our posting. Are you aware of another individual who is intrigued by Installing A Bathtub? Feel free to promote it. Thank you so much for going through it.
Book-Now
Report this page